The 10 best betafpv powerwhoop for 2019
Finding the best betafpv powerwhoop suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Finding the best betafpv powerwhoop suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Best betafpv powerwhoop
1. BETAFPV 10pcs Upgraded Tiny Whoop JST-PH 2.0 Power Whoop Female Connector Cable 55mm for Blade Inductrix
Feature
Upgrade JST-PH 2.0 connector, AKA PowerWhoop connector, the pins will not loose easilyConnector Female JST-PH 2.0
Length: 55mm ( NOT include the plug)
Must have for HV batteries and high performance
Wire: 24AWG
Description
Specification:
Connector : Female JST-PH 2.0, AKA PowerWhoop Female
Length: 55mm (NOT include the plug)
Wire: 24AWG
Package Including
10 * JST-PH 2.0 Female Cable
2. EUDAX 20 Sets Mini Micro Jst 2.0 Ph 2-Pin Connector Plug Male With 150mm Cable Female Connector Heat shrink tube for Li-Po Batteries
Feature
JST connector cable wire size: each cable wire length is approx. 15 cm/ 5.9 inches, the cable wire type is 26 AWG, micro size can meet your needsPH 2.0 2-pin connectors: the distance between connector's port is 2 mm, larger than 1.25 mm 2-pin connectors; Note: please check the port size before purchase
Cable wire material: the cable wire is electron wire, red cable connects positive pole, black cable connects negative pole
Wide applications: this micro JST PH 2.0 2-pin connectors set fits for Li-Po battery balance charger plug, good for helicopter, quadcopter, air plane, boat and car controller
Quantity: total 20 sets, including 20 x 2-pin PH 2.0 male connector plug with wire, 20 x 2-pin PH 2.0 female plug connectors, 40 x Electronic wires (each color for 20 pieces)40cm15.75inches1 Heat shrink tube
Description
Features:JST connector cable wires:
PH 2.0 2-pin connector wire cable is made of electron wire and zinc copper, durable and sturdy to use. Red cable wire connects positive pole and black cable wire connects negative pole, each cable length is 15 cm/ 5.9 inches, the type is 26 AWG, can meet your needs.
Applicable to:
This micro JST PH 2.0 2-pin connectors set fits for Li-Po battery balance charger plug, good for helicopter, quadcopter, air plane, boat and car controller.
Specifications:
Cable length: 15 cm
Type: 26 AWG
Cable material:electron wire
Plug connector material: plastic and metal
Cable wire color: black, red
Plug connector color: white
Quantity: 20 sets
Package includes:
20 x 2-Pin PH 2.0 male connector plug with wire
20 x 2-Pin PH 2.0 female plug connectors
20 x 15 cm Black Electronic wires
20 x 15 cm Red Electronic wires
40cm15.75inches1 Heat shrink tube
Note:
Please check the connector port size before purchase.
3. Racingirl NIDICI 15 Pairs Silicone 24 AWG Upgraded JST PH 2.0 Plug Connector 100MM 2 Pin Male Female Plug Connector Cable Wire for LED Lamp Strip RC Toys Battery
Feature
HELICOPTER LIPO BATTERY PLUG JST CONNECTOR: 24 AWG in type; The cable wire has male and female connector, approx. 100 mm/ 4 inches.2 PIN JST CONNECTOR: one side is for plugging the other side for welding, male connector match well with female connector, easy to install and use.
WIDE RANGE OF USES: these JST plug connectors are suitable for most mini RC helicopter, LED strip light and good for connecting motor, ESC battery, etc.
100% SILICONE INSULATED: Resistance High Temperature and High Pressure 200C 600V. According to market investigation, many customers feedback that JST plug connector which make from the PVC insulation is easy to burn during using even ruin the machine
PACKAGE INCLUDING: 15 pairs JST plug connector with cable wire (15 pieces female, 15 pieces male)
Description
Description:15 Pairs 24 AWG JST Plug Connector 2 Pin Male Female Plug Connector Cable Wire for LED Lamp Strip RC Toys Battery
Features:
JST connectors and cable wires:
Terminal spacing: 2.0 mm/ 0.08 inch, the pins are sturdy, will not loose easily. Cable wires are made of silicone in black and red color, red cable connects positive pole,
black cable connects negative pole. The cable wire type is 24 AWG, each is approx. 10 cm/ 3.9 inches in length (female connector length is not included), micro size can meet your needs.
Applicable to:
Suit well for Li-Po batteries balance charger plug, these micro JST PH 2.0 2-pin connectors are good partners
for helicopter, quadcopter, air plane, boat and car controller.
Specifications:
Cable length: approx. 10 cm/ 3.9 inches
Type: 24 AWG
Cable material: silicone
Plug connector material: plastic and metal
Cable wire color: black, red
Plug connector color: white
Quantity: 15 pieces of 2-pin male connectors with wire and 15 pieces of 2-pin female plug connectors with wire
Package includes:
15 x 2-Pin PH 2.0 female connector plug with wire
15 x 2-Pin PH 2.0 male connector plug with wire
Note:
Please check the connector port size before purchase.
4. BETAFPV 8pcs 300mAh HV 1S Lipo Battery 30C 4.35V with JST-PH 2.0 Powerwhoop Connector for Tiny Whoop Blade Inductrix
Feature
The upgrade version 1S HV 300mAh battery is the great choice of Tiny Whoop Blade inductrix with the connector plug of JST-PH2.0 PowerWhoop connector.Compared with 260mAh HV battery, you can get a longer flight time of 5'10'' and more power if you use it on Beta65s BNF.
This BETAFPV 1S 300mAh battery's weight is 7.7g with the larger capacity of 30C.
As a FPV battery, Don't over-charge, or over-discharge batteries. Don't put it beside the high temperature condition. Don't throw it into fire. Don't throw it into water.
Newly developed chemistry HV 1S Battery, longer flight time and safer charging situation. Safer, higher quality and more powerful rate brings you higher speed flying experience.
Description
BETAFPV 8pcs 300mAh HV 1S Lipo Battery 30C 3.8V with JST-PH 2.0 Powerwhoop Connector for Tiny Whoop Blade Inductrix Micro Mini Drone
Specification:
Item: 300 mAh HV 1S Lipo Battry
Capacity: 300mAh
Size: 58mm*11mm*6mm
Continuous Discharge Rate: 30C
Weight: 7.7g/pc
Flight time: 5'10'' on Beta65s
(If we use 260mah battery, we can get 4'10'' only on Beta65s.)
Caution:
Don't over-charge, or over-discharge batteries.
Don't put it beside the high temperature condition.
Don't throw it into fire.
Don't throw it into water.
Package Including
8 * 300mAh 1S Lipo Battery 30C 3.8V with JST-PH 2.0 Powerwhoop Connector
5. BETAFPV F4 Brushed Flight Controller FC with Betaflight OSD (No Receiver) for Micro Whoop Blade Inductrix Quadcopter
Feature
BETAFPV F4 brushed FC board bring a new era in FPV whoop technology. STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs, Build-in Betaflight OSD and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
30A continuous drain current MOSFET. Lower to 8.5m inner resistance value (4.5V). It has a noticeable power improvement in low battery voltage status or with 8x20/8.5x20 motors.
No receiver integrated. So pilots could connect any receiver, like the TBS crossfire rx etc.Designed to work with current Tiny Whoop or Blade Inductrix setups
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
Description
BETAFPV F4 Brushed Flight Controller FC with Betaflight OSD (No Receiveer) for Micro Whoop Blade Inductrix Quadcopter
BETAFPV F4 brushed FC board bring a new era in FPV whoop technology. STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs, Build-in Betaflight OSD and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.
Here share you a introduction and flight video made by a keen customer:
https://youtu.be/M5p2kJGLscU
Specification
Item F4 Brushed FC No RX with OSD
CPU: STM32F411CEU6
Six-Axis: MPU6000
ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.7g
Package:
1 * F4 OSD brushed flight controller ( 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Anti-vibration ruber dampers
6. BETAFPV F4 FC Brushed Flight Controller with SPI Frsky Receiver Betaflight OSD Smart Audio for Tiny Whoop Micro Racing Drone
Feature
The default configuration from factory is Frsky D16 mode (FRSKY_X). Built in Frsky receiver is compatible with Taranis, Taranis Plus, X9E, Horus X12S, XJT Modules. In Betaflight Configuration, it should be setted as FRSKY_D receiver (aka Frsky D8 mode) or FRSKY_X receiver (aka Frsky D16 mode) in SPI RX mode.This is a SPI Frsky receiver. Binding easier than before, no need to click the bind button when power on. Manual: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector. Designed to work with current Tiny Whoop or Blade Inductrix setups
F411 Processor can reach to 100MHz, much faster than the F3 Flight Controller with 72Mhz. Integrated with Frsky receiver only. Upgraded to 30A Lower Resistance MOSFET, Firmware version: betaflight_matekf411rx_3.4.0. Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode). Support Smart Audio.
Some basic guidance and typical FAQ, please check it here : https://betafpv.freshdesk.com/support/solutions
Description
BETAFPV F4 Brushed Flight Controller Integrated with OSD and Frsky Receiver for Tiny Whoop Drone.
BETAFPV F4 brushed FC board bring a new era in FPV whoop technology. STM32F411 100MHz high performance MCU, 30A lower resistance MOSFETs, SPI Frsky Rx, Build-in Betaflight OSD and polar reversed protection. All of these is backed by the same reliability and warranty of all BETAFPV FC boards.
Binding Procedure--Easier than usual. No need to click the bind button when power on.
a.Power on the board, connecting the battery or USB power. Then the green receiver LED start to flash.
b.Press the bind button for 3s. Then the green receiver LED will be solid on. It means the receiver is in bind mode and you could start to bind your radio transmitter.
Checking here: https://betafpv.freshdesk.com/support/solutions/articles/27000021366-how-to-bind-your-radio-transmitter-brushed-fc-board
Specifications:
CPU: STM32F411CEU6
Six-Axis: MPU6000
ESC: All FETs are rated at 30A maximum. Support 6x15mm/7x20mm/8x20mm/8.5x20mm etc motors.
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight MATEKF411RX 3.4.0
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: SPI Frsky D8 protocol (AKA FRSKY_D on Betaflight Configuration)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.7g
Here is a using video shared by Shutterbug:
https://www.youtube.com/watch?v=M5p2kJGLscU
Package:
1 * F4 OSD brushed flight controller (55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm)
4 * Anti-vibration ruber dampers
7. Crazepony 4pcs 230mAh HV 1S Lipo Battery 30C 3.8V for Tiny Whoop Blade Inductrix JST-PH 2.0 Connector
Feature
Newly developed chemistry HV 1S Battery, high voltage gets longer lifetime and safer charging situationCapacity: Standard voltage (4.2v, 230mah)or High voltage (4.35v, 250ish mah)
Tiny Whoop Blade inductrix future choice of battery
The connector plug: JST-PH2.0 AKA High current ultra micro, Powerwhoop , mCPX
Dimension: 54mm * 12.5mm * 6mm, Weight: 6.3g/per unit
Description
4pcs 230mAh HV 1S Lipo Battery 30C 3.8V for Tiny Whoop Blade Inductrix JST-PH 2.0 ConnectorFeatures:
Item: HV 1S Crazepony Lipo Battery
Rate: 30C
Dimension: 54mm * 12.5mm * 6mm
Weight: 6.3g/per unit
Capacity: 230mAh in standard voltage, 250mAh in high voltage
The connector plug: JST-PH 2.0 AKA High current ultra micro, Powerwhoop, mCPX
This battery is lighter than the usual 230mah battery, and can be charged to either standard voltage (4.2v, 230mah) or high voltage (4.35v, 250ish mah).
This is newly developed chemistry for a longer lifetime and safer charging situation. This battery will give you higher rpms (more power) and a considerably longer flight time.
High density with great safety fits Tiny Whoop
--------------------------------------------------------
Package Including
4 * 230mAh HV 1S Lipo Battery 30C 3.8V JST-PH 2.0 Connector
8. BETAFPV 3 Set 7x20mm 17500KV Brushed Motors with JST-1.25 Connector for Micro Tiny Whoop BETA75 Tiny7 CX-95W etc
Feature
Recommended parts list are Beta75 frame, 40mm 3-blades props and 260mAh 1S Whoop battery with PowerWhoop connector.Motor Diameter: 7mm, Motor Length: 20mm, With 1.25mm JST Plug
Spare motors for BETA75, Tiny7, CX-95W etc
Basic Edition 17500kv or 65000rpm / 3.7V
Weight: about 3.5g
Description
This is our new fastest speed 7mm micro motor. These motors are design for pure speed. It comes to performance and motor lifetime. Recommended parts list are Beta75 frame, 40mm 3-blades props and 260mAh 1S Whoop battery with PowerWhoop connector.Specifications:
Width: 7mm
Height: 20mm
Shaft Diameter: 1mm
Shaft length: 5mm
Speed: 17500kv or 65000rpm / 3.7V
Wire Length: 8cm
JST 1.25 connector
Clockwise: Red and Blue wires
Counter Clockwise: White and Black wires
Package:
12 * 17500KV 7x20mm motors (6CW + 6CCW)
9. BETAFPV 5pcs JST-PH 2.0 PowerWhoop Double Female Connector Cable Silicone 55mm 24AWG for 2S Whoop Drone Like Beta75X and Beta65X etc
Feature
This double connectors cable is just for 2S whoop drone, so pilot can use the same 1S whoop style batteries like 260mAh or 300mAh battery to fly the 2S drone Beta65X or Beta75X.The 5pcs JST-PH 2.0 PowerWhoop Female Connector Cable is with the standard connector for whoop drones, JST-PH 2.0 and AKA PowerWhoop.
The material of the power cable is silicone, with the thickness of 24AWG.
The length of the double female connector cable is 55mm not include the plug, and the weight is about 1.2g/pcs.
Any technical support needed please contact : [email protected].
Description
BETAFPV 5pcs JST-PH 2.0 PowerWhoop Double Female Connector Cable Silicone 55mm 24AWG for 2S Whoop Drone like Beta75X and Beta65X etc
Specifications:
Item: 2S Whoop Cable Pigtail (JST-PH 2.0)
Material:Silicone
Connector:Female JST-PH 2.0, AKA PowerWhoop Female
Weight:1.2g/pcs
Length:55mm (Not including the plug)
Thickness: 24AWG
Application: On 2S BNF for 2pcs 260mah batteries or 2pcs 300mah batteries
Package:
5 * 2S Whoop Drone Female Power Cable
10. BETAFPV 8pcs 300mAh 1S Lipo Battery HV FPV Battery 30C 4.35V with JST-PH 2.0 Powerwhoop Connector for Tiny Whoop 65mm Frame Kit Micro Mini Drone
Feature
Upgrade Version of 1S 300mAh Battery: The upgrade version 1S HV 300mAh battery is the great choice of Tiny Whoop Blade inductrix with the connector plug of JST-PH2.0 PowerWhoop connnector.Small Size and Light Weight: This BETAFPV 1S 300mAh battery's weight is 7.7g with the larger capacity of 30C.
Longer Flight Time:Compared with 260mAh HV battery, you can get a longer flight time of 5'10'' and more power if you use it on Beta65s BNF.
Caution: As a FPV battery, Don't over-charge, or over-discharge batteries. Don't put it beside the high temperature condition. Don't throw it into fire. Don't throw it into water.
Best Customer Service: Our Humming Store provide more combo kits for you and your devices with LESS Money and FREE Shipping !!!
Description
BETAFPV 8pcs 300mAh 1S Lipo Battery HV FPV Battery 30C 4.35V with JST-PH 2.0 Powerwhoop Connector for Tiny Whoop 65mm Frame Kit Micro Mini DroneSpecification:
Item: 300 mAh HV 1S Lipo Battry
Capacity: 300mAh
Size: 57mm*12mm*6mm
Continuous Discharge Rate: 30C
Weight: 7.7g/pc
Flight time: 5'10'' on Beta65s
(If we use 260mah battery, we can get 4'10'' only on Beta65s.)
Caution:
Don't over-charge, or over-discharge batteries.
Don't put it beside the high temperature condition.
Don't throw it into fire.
Don't throw it into water.
Package Including
8 * 300mAh 1S Lipo Battery 30C 3.8V with JST-PH 2.0 Powerwhoop Connector