Best duplex mmdvm
If you looking for duplex mmdvm then you are right place. We are searching for the best duplex mmdvm on the market and analyze these products to provide you the best choice.
If you looking for duplex mmdvm then you are right place. We are searching for the best duplex mmdvm on the market and analyze these products to provide you the best choice.
Best duplex mmdvm
1. TOOGOO MMDVM_HS_Dual_Hat Duplex MMDVM Hotspot P25 DMR YSF NXDN Pi Revision 1.2 + OLED
Feature
Duplex variant of MMDVM_HS_HatThis PCB uses the MMDVM_HS . It has two ADF7021 onboard and allows for duplex operation with two time slots on DMR.
Revision 1.2
An accidentially deleted 3v3 wire has been added back to the PCB layout. BOM, Mouser cart and stencil stay the same as for rev1.1.
High performance 32-bit ARM processor
Description
* TOOGOO is a registered trademark. ONLY Authorized ller of TOOGOO can ll under TOOGOO listings.Our products will enhance your experience to unparalleled inspiration.TOOGOO(R)MMDVM_HS_Dual_Hat Duplex MMDVM Hotspot P25 DMR YSF NXDN Pi Revision 1.2 + OLED
Fully tested
Supports DMR, P-25,D-Star and System Fusion
Onboard LEDs to show status (Tx,Rx,PTT,Mode)
Up to 10mW RF power
SMA antenna connector,Antenna included
Mounts cleanly on all current Raspberry Pi's including the Pi Zero
The firmware is pre-loaded and is easily upgraded via software.
Open source 3D printable ca available
UHF 430-450 MHz,43hz and 900MHz
VHF 144 220 Opera FREQ
The upper part is TX,the lower is RX antenna.
UHF+VHF
SMA,antenna
Modem lect:STM32_HS_GPIO
t TX frequency,RX frequency
TX,RX frequency had better 10M or more apart.
SLOT1,SLOT2 support.
colour:green
Material:PCB+plastic
size:70*60*20mm
Package Contents:
1 *MMDVM HotSPOT Module + OLED
2 *antenna
Note:
Without shell
Not include the raspberry pi
The firmware is pre-loaded. if you want update pls Click Updated site
Only the above package content, other products are not included.
Note: Light shooting and different displays may cau the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
2. TOOGOO Duplex MMDVM Hotspot Support P25 DMR YSF Raspberry Pi 2 Antenna US Ship
Feature
High performance 32-bit ARM processor. Fully testedSupports DMR, P-25,D-Star and System Fusion.Onboard LEDs to show status (Tx,Rx,PTT,Mode)
Up to 10mW RF power.SMA antenna connector,Antenna included
Mounts cleanly on all current Raspberry Pi's including the Pi Zero. The firmware is pre-loaded and is easily upgraded via software.
Open source 3D printable case available. Uhf 430-450 MHz,433mhz and 900MHz
Description
* TOOGOO is a registered trademark. ONLY Authorized seller of TOOGOO can sell under TOOGOO listings.Our products will enhance your experience to unparalleled inspiration.TOOGOO(R) Duplex MMDVM Hotspot Support P25 DMR YSF for Raspberry Pi with 2 Antenna US Ship
VHF 144 220 Opera FREQ
Note:
Without shell
Not include the raspberry pi
The firmware is pre-loaded.Please do not upgrade the firmware by yourself.
The upper part is TX,the lower is RX antenna.
UHF+VHF
SMA,antenna
Modem select: STM32_HS_GPIO
Set TX frequency,RX frequency
TX,RX frequency had better 10M or more apart.
SLOT1,SLOT2 support.
color: green
Material: ABS
Package Contents: 2 x Antenna + MMDVM HotSPOT Module
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
3. SODIAL Duplex MMDVM Hotspot Support P25 DMR YSF for Raspberry Pi with 2 Antenna US Ship
Feature
High performance 32-bit ARM processor. Fully testedSupports DMR, P-25,D-Star and System Fusion.Onboard LEDs to show status (Tx,Rx,PTT,Mode)
Up to 10mW RF power.SMA antenna connector,Antenna included
Mounts cleanly on all current Raspberry Pi's including the Pi Zero. The firmware is pre-loaded and is easily upgraded via software.
Open source 3D printable case available. Uhf 430-450 MHz,433mhz and 900MHz
Description
* SODIAL is a registered trademark. ONLY Authorized seller of SODIAL can sell under SODIAL listings.Our products will enhance your experience to unparalleled inspiration.SODIAL(R) Duplex MMDVM Hotspot Support P25 DMR YSF for Raspberry Pi with 2 Antenna US Ship
VHF 144 220 Opera FREQ
Note:
Without shell
Not include the raspberry pi
The firmware is pre-loaded.Please do not upgrade the firmware by yourself.
The upper part is TX,the lower is RX antenna.
UHF+VHF
SMA,antenna
Modem select: STM32_HS_GPIO
Set TX frequency,RX frequency
TX,RX frequency had better 10M or more apart.
SLOT1,SLOT2 support.
color: green
Material: ABS
Package Contents: 2 x Antenna + MMDVM HotSPOT Module
Only the above package content, other products are not included.
Note: Light shooting and different displays may cause the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
4. WiFi Digital Voice Modem for MMDVM Hotspot Spot Radio Station Mode DSTAR P25 DMR
Feature
Suit for Raspberry Pi 3,Raspberry Pi Zero WSupport:D-STAR, P25, DMR and work with UHF
Basic Setup: Set the same freq as Radio Mobilefor example : 433.550000MHZ DMR
WIFI SSID:GARY/PASSWORD:13537701008 (Need the 2.4GHz SSID as the Pi Zero W doesn't support 5.8GHz)
Power supply: Mobile charger or a USB cable connected to your computer or laptop. The Hotspot will also work mobile in your vehicle if you Tether it to your mobile phone network.
Description
Wifi Digital Voice Modem for MMDVM Hotspot Spot Radiois an easy, convenient and ready to use Multi-mode Hotspot that supports D-STAR/P25/DMR
Suit for Raspberry Pi 3,Raspberry Pi Zero W
Support:D-STAR, P25, DMR and work with UHF
Basic Setup: 433.550000MHZ DMR
WIFI SSID:GARY/PASSWORD:13537701008 (Need the 2.4GHz SSID as the Pi Zero W doesn't support 5.8GHz)
Software:Pi-Star
Power supply: Mobile charger or a USB cable connected to your computer or laptop. The Hotspot will also work mobile in your vehicle if you Tether it to your mobile phone network.
Note: All designs will be contributed on MMDVM open source project.
Package content:
1. OLED display x1 (installed on board)
2. Raspberry Pi Zero W x1
3. MMDVM hotspot board x1
4. 8G TFT card x1
5. Aluminum Shell x1
6. 433Mhz Antenna x1
5. C4 Labs DRPi-1NSX case for Raspberry Pi 3 B+, Duplex MMDVM v1.0, 2.4 Enhanced Nextion Screen (Included) ~ (Black Ice)
Feature
Full body coverage for Raspberry Pi, Duplex MMDVM v1.0 dual antenna, and Nextion screen (not waterproof)Includes a 2.4 Enhanced Nextion screen*
Case can fit a ZUMspot OR JumboSPOT
For Raspberry Pi 3B+, 3B, 2B, and B+ (not included), Duplex MMDVM v1.0 (not included), and a 2.4 Enhanced Nextion Screen (included)
Designed and Made in Tacoma, WA USA
Description
The DRPi-1NSX case allows you to elegantly combine the Raspberry Pi, Duplex MMDVM, and a 2.4 Enhanced Nextion Screen*, which is included. We go the extra mile to make sure everything we make feels solid and looks great. We use stainless steel hardware and acrylic to construct this case and guarantee you will love it as much as we do. The Nextion Enhanced NX3224K024 is a powerful 2.4 HMI TFT display, with 16MB Flash data storage space, 1024 byte EEPROM, and 3584 byte RAM. *Please note that connecting the Nextion screen to your set-up may require additional soldering of pins or wires not covered in these case instructions.6. DIY Kits Duplex MMDVM Hotspot Support P25 DMR YSF + 2PCS Antenna for WD
Feature
Package Includes: 1 x MMDVM HotSPOT Module | 2 x Antenna | 2 x Pin Headers- Up to 10mW RF power.
- Open source 3D printable case available.
- Uhf 430-450 MHz,433mhz and 900MHz.
- High performance 32-bit ARM processor.
Description
Features:- Up to 10mW RF power.
- Open source 3D printable case available.
- Uhf 430-450 MHz,433mhz and 900MHz.
- High performance 32-bit ARM processor.
- SMA antenna connector,Antenna included.
- Supports DMR, P-25,D-Star and System Fusion.
- Onboard LEDs to show status (Tx,Rx,PTT,Mode).
-The firmware is pre-loaded and is easily upgraded via software.
- Mounts cleanly on all current WD 's including the Pi Zero.
The upper part is TX,the lower is RX antenna.
UHF+VHF
SMA,antenna
Modem select: STM32_HS_GPIO
Set TX frequency,RX frequency
TX,RX frequency had better 10M or more apart.
SLOT1,SLOT2 support.
Notice:
- Without shell.
- Not include the WD .
- The firmware is pre-loaded.Please do not upgrade the firmware by yourself.
Package includes:
1 x MMDVM HotSPOT Module
2 x Antenna
2 x Pin Headers
7. Raspberry Pie MMDVM Digital Radio Wireless Hot Spot hotspot Mini Relay Duplex
Feature
Support Raspberry pi and raspberry pi ZEROStrengthen the scatter system, no longer worry about the summer temperature burst
This board can be directly connected to Nextion, TJC serial serial screen, without USB-TTL conversion module
Require some MMDVM knowledge,suitable to DIY with raspberry pi
8. SODIAL MMDVM_HS_Dual_Hat Duplex MMDVM Hotspot P25 DMR YSF NXDN Pi Revision 1.2 + OLED
Feature
Duplex variant of MMDVM_HS_HatThis PCB uses the MMDVM_HS . It has two ADF7021 onboard and allows for duplex operation with two time slots on DMR.
Revision 1.2
An accidentially deleted 3v3 wire has been added back to the PCB layout. BOM, Mouser cart and stencil stay the same as for rev1.1.
High performance 32-bit ARM processor
Description
* SODIAL is a registered trademark. ONLY Authorized ller of SODIAL can ll under SODIAL listings.Our products will enhance your experience to unparalleled inspiration.SODIAL(R)MMDVM_HS_Dual_Hat Duplex MMDVM Hotspot P25 DMR YSF NXDN Pi Revision 1.2 + OLED
Fully tested
Supports DMR, P-25,D-Star and System Fusion
Onboard LEDs to show status (Tx,Rx,PTT,Mode)
Up to 10mW RF power
SMA antenna connector,Antenna included
Mounts cleanly on all current Raspberry Pi's including the Pi Zero
The firmware is pre-loaded and is easily upgraded via software.
Open source 3D printable ca available
UHF 430-450 MHz,43hz and 900MHz
VHF 144 220 Opera FREQ
The upper part is TX,the lower is RX antenna.
UHF+VHF
SMA,antenna
Modem lect:STM32_HS_GPIO
t TX frequency,RX frequency
TX,RX frequency had better 10M or more apart.
SLOT1,SLOT2 support.
colour:green
Material:PCB+plastic
size:70*60*20mm
Package Contents:
1 *MMDVM HotSPOT Module + OLED
2 *antenna
Note:
Without shell
Not include the raspberry pi
The firmware is pre-loaded. if you want update pls Click Updated site
Only the above package content, other products are not included.
Note: Light shooting and different displays may cau the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
9. TOOGOO MMDVM Duplex Hotspot Support P25 DMR YSF NXDN DMR Slot 1+ Slot 2 Raspberry pi
Feature
High performance 32-bit ARM processorFully tested
Supports DMR, P-25,D-Star and System Fusion
Onboard LEDs to show status (Tx,Rx,PTT,Mode)
Up to 10mW RF power
Description
* TOOGOO is a registered trademark. ONLY Authorized ller of TOOGOO can ll under TOOGOO listings.Our products will enhance your experience to unparalleled inspiration.TOOGOO(R) New MMDVM DUPLEX hotspot Support P25 DMR YSF NXDN DMR SLOT 1+ SLOT 2 for Raspberry pi
SMA antenna connector,Antenna included
Mounts cleanly on all current Raspberry Pi's including the Pi Zero
The firmware is pre-loaded and is easily upgraded via software.
Open source 3D printable ca available
Uhf 430-450 MHz,43hz and 900MHz
The upper partis TX,the lower is RX antenna.
UHF+VHF
SMA,antenna
Modem lect: STM32_HS_GPIO
t TX frequency,RX frequency
TX,RX frequency had better 10M or more apart.
SLOT1,SLOT2 support.
VHF 144 220 Opera FREQ
Install the firmware with bootloader support for USB connection
If you want to u the device via USB port you have to install a bootloader and build the firmware with bootloader support. As the raw device cannot be ud with USB you have to u a USB-rial adapter or STlink device
Note:
Without shell
Not include the raspberry pi
The firmware is pre-loaded.Plea do not upgrade the firmware by yourlf.
colour: Black + green
Material: PCB+FR4
Package Contents:
1 * MMDVM Module
2 * Antenna
1 * Instruction manual
Only the above package content, other products are not included.
Note: Light shooting and different displays may cau the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.
10. TOOGOO MMDVM Duplex Hotspot Support P25 DMR YSF NXDN DMR Slot 1 Slot 2 for Raspberry pi
Feature
High performance 32-bit ARM processorFully assembled and tested
Supports DMR, P-25, D-Star and System Fusion
Onboard LEDs to show status (Tx, Rx, PTT, Mode)
Up to 10mW RF power
Description
* TOOGOO is a registered trademark. ONLY Authorized ller of TOOGOO can ll under TOOGOO listings.Our products will enhance your experience to unparalleled inspiration.TOOGOO(R)MMDVM DUPLEX hotspot Support P25 DMR YSF NXDN DMR SLOT 1 SLOT 2 for Raspberry pi
SMA antenna connector, UHF/VHF antenna included
Mounts cleanly on all current Raspberry Pi's including the Pi Zero
The firmware is pre-loaded and is easily upgraded via software.
UHF 433 900 MHZ ,VHF 144 220 MHZ Opera FREQ
TX,RX not the same Freq,support UHF+UHF , UHF+VHF Mode
TX,RX not the same Freq,support UHF+UHF , UHF(RX)+VHF(TX) ,VHF(TX)+UHF(RX) mode
Support and tested with PI-STAR
colour:green
Material:PCB+plastic
size:70*60*20mm
Package Contents:
1*MMDVM module
2* antenna
Only the above package content, other products are not included.
Note: Light shooting and different displays may cau the color of the item in the picture a little different from the real thing. The measurement allowed error is +/- 1-3cm.